8331 ja 7360 5.1 järjestelmä

8331 säteilee ääntä yhdestä pisteestä, jonka ansiosta huoneen vaikutus tarkkuuteen vähenee entisestään, lopputuloksena kirkas ja värittymätön tilavaikutelma.


Ratkaisun tuotteet:

5 × 8331A SAM™ Studiomonitori
1 × 7360A SAM™ Studiosubwoofer

Ratkaisun tuotteet:

8331A SAM™ Studiomonitori

SPL

104 dB

Taajuusvaste

45 Hz - 37 kHz (-6dB)

Mitat

H 305 x W 189 x D 212 mm, with Iso-Pod™ (muunna tuumiksi)

7360A SAM™ Studiosubwoofer

SPL

109 dB

Taajuusvaste

19 Hz - 150 Hz (-6dB)

Mitat

H 527 x W 462 x D 363 mm, (muunna tuumiksi)

Avainteknologiat

Smart Active Monitor (SAM™)

Minimum Diffraction Coaxial (MDC™)

Acoustically Concealed Woofers (ACW™)

Directivity Control Waveguide (DCW™)

Minimum Diffraction Enclosure (MDE™)

Reflex Port Design

Protection Circuitry

Intelligent Signal Sensing (ISS™)

Optimized Amplifiers

Active Crossovers

Iso-Pod™ Stand

Versatile Mountings

Bass Management

Laminar Spiral Enclosure (LSE™) Technology

Etsi jälleenmyyjäsi

Kirjoita kenttään sijaintisi ja löydä lähin jälleenmyyjäsi.

Dokumentit

UKK

Our most compact Home Audio loudspeaker, the G One combines huge performance with beautiful aesthetics. Ideal for smaller spaces, it's perfect for computer sound, music playback or home theatre.

Which SAM™ Products You Are Going to Mix With the Classic 8000 Series?
Mixing 8000 Series and SAM™ monitors is not recommended

We do not recommend mixing Classic 8000 Series monitors with SAM™ Monitors.
If the analogue input sensitivity of 8000 Series and SAM™ Series monitors are the same, Genelec SAM™ Monitors exhibit a slightly larger latency (< 5 ms) than 8000 Series monitors. Therefore Classic 8000 Series and SAM™ Series monitors should not be mixed in a stereo pair or multichannel setup.

It is alright to mix Classic 8000 Series with SAM™ Subwoofers

However, it is okay to mix the Classic 8000 Series monitors with SAM™ Subwoofers. Any Classic 8000 Series monitors can be used with SAM™ Subwoofers, in any stereo or multichannel setup.

Setting the room response calibration controls

Genelec monitors are calibrated flat in anechoic free field conditions. When the monitor is placed in a room close to walls or other boundaries, the low frequency output of the monitor increases. To achieve a flat low frequency response an adjustment of typically -4 dB on the bass tilt control is used. Genelec also provides a bass roll-off control to compensate for any remaining excessive LF energy around the low cut-off frequency.
Genelec GLM AutoCal can implement a more precise compensation after measuring the acoustic effects produced by the monitor’s installation location.

Differences in room reverberation time and listening distance can lead to changes being required in the treble region so treble tilt is fitted to most of the models in the Genelec range.

In three-way monitors and large main systems there are additional driver controls for the bass level, mid level and treble level which enable very fine adjustment of the frequency response so that the monitors can be placed in many different listening environments, whilst still achieving a consistent and neutral sound reproduction.

The best way to set the room response controls of a Genelec monitor is by taking an acoustical measurement at the listening location, using a measurement system for those products that offer local controls (DIP switches) on the monitor or subwoofer, or by using GLM AutoCal for the SAM™ (Smart Active Monitoring) products.