7382A

SAM™ Studiosubwoofer

Viiteentoista hertsiin ulottuvalla toistollaan ja 130 desibelin äänenpaineellaan 7382A on Genelecin kaikkien aikojen suorituskykyisin subwoofer.

Smart Active Monitor (SAM™)

Optimized Amplifiers


SPL

129 dB

Taajuusvaste

15 Hz - 100 Hz (-6 dB)

Mitat

H 625 x W 1400 x D 558 mm, (muunna tuumiksi)

Voimaa ja joustavuutta

7382 sopii äänitysstudioihin, elokuvaäänen miksaukseen, masterointiin, jälkituotantoon, elektronisen musiikin toistoon ja korkeatasoisiin kotiteattereihin. Tarkan kalibroitavuutensa ja bassonhallintansa ansiosta se on helppo integroida erilaisiin järjestelmiin klassisesta stereosta yli 40 kaiuttimen immersiivisiin äänijärjestelmiin. 7382 on varustettu kolmella viidentoista tuuman elementillä, joita käyttää tehokas D-luokan vahvistin. Suora refleksiputki kulkee kotelon takaseinää pitkin, joten virtausäänet ja särö on saatu minimoitua. Tämä yhdistelmä takaa tarkan ja vääristymättömän toiston suurillakin äänenpainetasoilla aina alimpiin taajuuksiin asti.  

Täysin optimoitu bassohallinta

Täysin optimointu kuuntelu Genelecin Smart Active Monitor (SAM™) -tuoteperheen jäsenenä 7382 hyödyntää Genelec Loudspeaker Manager (GLM™) -tietokoneohjelman monipuolisia ominaisuuksia. Subwooferin käyttöönotto, integrointi muuhun kaiutinjärjestelmään ja kalibrointi tapahtuvat vaivattomasti ja täsmällisesti GLM:n avulla, riippumatta järjestelmän laajuudesta. GLM toimii myös kaiutinjärjestelmän hallintatyökaluna Mac- tai PC-ympäristöissä. Sen avulla voit asettaa kuunteluvolyymin yleisten tuotantostandardien mukaiseksi, vaihtaa joustavasti ääniformaatteja, kaiutinyhdistelmiä ja optimoituja kuuntelualueita – monista muista hyödyllisistä ominaisuuksista puhumattakaan.

Genelec

7382A SAM™ Studiosubwoofer

Värivaihtoehdot:
Pakkaus sisältää:

1 x 7382A subwoofer
1 x RAM-SW vahvistinyksikkö
1 x virtajohto 1,8 m
1 x RJ45 kaapeli 5 m
1 x Speakon signaalikaapeli 10 m
1 x käyttöohje

Genelec

7382A SAM™ Studiosubwoofer

Värivaihtoehdot:

Tekniset tiedot

SPL

129 dB

Vahvistimen teho

2500 W Basso (Class D)

Taajuusvaste

15 Hz - 100 Hz ("-6 dB")

Kaiutinelementtien mitat

3 x 381 mm Basso (muunna tuumiksi)

Mitat

H 625 x W 1400 x D 558 mm, (muunna tuumiksi)

Paino

145 kg / 319.7 lb

Liitännät

3 x XLR Analoginen Sisääntulo

2 x XLR Analoginen Ulostulo

1 x XLR AES/EBU Sisääntulo

1 x XLR AES/EBU Ulostulo

2 x RJ45 Ohjaus

Avainteknologiat

Smart Active Monitor (SAM™)

Optimized Amplifiers

Intelligent Signal Sensing (ISS™)

Bass Management

Protection Circuitry

Active Crossovers


Referenssit

Using GLM | Walkthrough

Using GLM | The foundations

Using GLM | Controlling GLM with MIDI

Using GLM | GRADE Room Acoustic Report

Using GLM | Calibration Group IDs

Using GLM | Accounts and product registration

Using GLM | The technical details


Etsi jälleenmyyjäsi

Kirjoita kenttään sijaintisi ja löydä lähin jälleenmyyjäsi.

Rajausvaihtoehdot
X Rajausvaihtoehdot
All
Studiomonitorit
Kotikaiuttimet
AV-asennus
Tekninen huolto
Showroom
Experience Centre
SAM Certified
Smart IP Certified
Maa

Dokumentit

UKK

The Classic 8000 Series monitors have an analogue input. The 7200 Series SAM subwoofers have AES/EBU digital outputs only. However, other 7300 Series SAM subwoofers have analogue inputs and outputs and can be used also with analogue monitors.

Which SAM™ Products You Are Going to Mix With the Classic 8000 Series?
Mixing 8000 Series and SAM™ monitors is not recommended

We do not recommend mixing Classic 8000 Series monitors with SAM™ Monitors.
If the analogue input sensitivity of 8000 Series and SAM™ Series monitors are the same, Genelec SAM™ Monitors exhibit a slightly larger latency (< 5 ms) than 8000 Series monitors. Therefore Classic 8000 Series and SAM™ Series monitors should not be mixed in a stereo pair or multichannel setup.

It is alright to mix Classic 8000 Series with SAM™ Subwoofers

However, it is okay to mix the Classic 8000 Series monitors with SAM™ Subwoofers. Any Classic 8000 Series monitors can be used with SAM™ Subwoofers, in any stereo or multichannel setup.

Setting the room response calibration controls

Genelec monitors are calibrated flat in anechoic free field conditions. When the monitor is placed in a room close to walls or other boundaries, the low frequency output of the monitor increases. To achieve a flat low frequency response an adjustment of typically -4 dB on the bass tilt control is used. Genelec also provides a bass roll-off control to compensate for any remaining excessive LF energy around the low cut-off frequency.
Genelec GLM AutoCal can implement a more precise compensation after measuring the acoustic effects produced by the monitor’s installation location.

Differences in room reverberation time and listening distance can lead to changes being required in the treble region so treble tilt is fitted to most of the models in the Genelec range.

In three-way monitors and large main systems there are additional driver controls for the bass level, mid level and treble level which enable very fine adjustment of the frequency response so that the monitors can be placed in many different listening environments, whilst still achieving a consistent and neutral sound reproduction.

The best way to set the room response controls of a Genelec monitor is by taking an acoustical measurement at the listening location, using a measurement system for those products that offer local controls (DIP switches) on the monitor or subwoofer, or by using GLM AutoCal for the SAM™ (Smart Active Monitoring) products.

hello

Kaipaatko tukea?


Etsi tukiportaalistamme useimmin kysyttyjä kysymyksiä:

Voit myös lähettää asiakaspalvelutiimille kysymyksen tästä.