Genelec 1024C
System Specifications
| Lower cut-off frequency, -3 dB: | < 32 Hz | |
| Upper cut-off frequency, -3 dB: | > 20 kHz | |
| Free field frequency response tolerance of system | ± 3 dB | |
| Maximum continuous sine wave acoustic output @ 1m on axis in half space | > 116 dB | |
| Maximum continuous RMS acoustic output in same conditions with IEC-weighted noise: | > 116 dB | |
| Maximum peak acoustic output per pair at engineers' site, speakers @ 2 m from the engineer, with music material | > 122 dB | |
| A -20 dBu signal input will produce 97 dB SPL in free field @1 m on axis with all controls set at the 'CAL' position. The CAL position is the 0 dB position of all tone controls and the maximum sensitivity position of the input level control. See specification in the Crossover Section | ||
| Self generated noise level in free field @ 1m on axis | < 15 dB |
|
| Harmonic distortion at 100 dB SPL @ 1m on axis f < 200 Hz f > 200 Hz |
< 3 % < 1 % |
|
| Drivers Bass Mid Treble |
15" cone (385 mm) 5" cone (120 mm) 1 1/8" dome (28 mm) |
|
| Weight | 150 lb (68 kg) | |
| Dimensions: Height Width Depth |
19 1/2" (495 mm) 35 1/2" (900 mm) 18 1/4" (464 mm) |
|
Amplifier |
||
| Bass amplifier output power at 4 ohm load: continuous momentary |
350 W 490 W |
|
| Midrange amplifier output power at 8 ohm load: continuous momentary |
50 W 250 W |
|
| Treble amplifier output power at 8 ohm load: continuous momentary |
8 W 250 W |
|
| Mid and treble channel continuos output power is limited by the driver unit protection processor | ||
| Slew rate | 100 V /µs | |
| Amplifier system distortion at nominal output THD SMPTE-IM CCIF-IM DIM100 |
< 0,05 % < 0,1 % < 0,1 % < 0,1 % |
|
| Signal to Noise ratio, from shorted system input to channel output, referred to full output: bass midrange treble |
104 dB 100 dB 94 dB |
|
| Mains voltage | 100/110/220/240 VAC | |
| Voltage Operation Range | ± 10 % | |
| Power consumption, idle full output |
50 VA 700 VA |
|
Crossover |
||
| Input connector: XLR female | pin 2 + pin 3 - |
|
| Input impedance | 10 k balanced | |
| Continuously variable input level for maximum output: @10 dB attenuation @0 dB attenuation |
from + 9 dBu to + 19 dBu from -1 dBu to + 9 dBu |
|
| Subsonic filter | down 12 dB @ 10 Hz re 100 Hz level |
|
| Ultrasonic filter | down 12 dB @ 50 kHz re 10 kHz level |
|
| Crossover frequency bass / midrange midrange / treble |
400 Hz 3.5 kHz |
|
| Tone control operation range in 1 dB steps bass midrange treble |
from 0 dB to -6 dB from 0 dB to -6 dB from 0 dB to -6 dB |
|
| The 0 dB position is the 'CAL' position (switch position number 7) | ||
| Bass roll-off filter in a 4 dB step: | from -4 dB to 0 dB @ 32 Hz | |
| The 0 dB position is the 'CAL' position (switch position number 2) | ||
| Bass tilt control in 2 dB steps: | from 0 dB to -6 dB @ 50 Hz | |
| The 0 dB position is the 'CAL' position (switch position number 4) | ||
All data subject to change without prior notice |
||